361 found, showing page 1 of 10
$11.99
6-8X3/4 PLA ANCHOR W/SCR
Recommended for light-duty static applications where holding power is not critical. For use in concrete, block, brick, and wallboard. Screws included.
View Details
100PC 1/4"USS FLT WASHER
Zinc steel flat washer with wide pattern is used to spread the load of a screwed fastening or when the hole is a larger diameter than the fixing nut.
View Details
$2.60
*ANCHRBLT&NUT 5/8x10
Bright anchor bolt with nut - no washer. For attaching bottom plate or sill plate to newly poured concrete foundation. Meets ASTM A307 specifications. 50-pieces per bag.
View Details
$2.80
*ANCHRBLT&NUT 5/8x12
Bright anchor bolt with nut - no washer. For attaching bottom plate or sill plate to newly poured concrete foundation. Meets ASTM A307 specifications. 50-pieces per bag.
View Details
$2.49
*ANCHRBLT&NUT 5/8x14
Bright anchor bolt with nut - no washer. For attaching bottom plate or sill plate to newly poured concrete foundation. Meets ASTM A307 specifications. 50-pieces per bag.
View Details
$2.40
*ANCHRBLT&NUT 3/4x12
Bright anchor bolt with nut - no washer. For attaching bottom plate or sill plate to newly poured concrete foundation. Meets ASTM A307 specifications. 50-pieces per bag.
View Details
100PC 5/16"USS FL WASHER
Zinc steel flat washer with wide pattern is used to spread the load of a screwed fastening or when the hole is a largerdiameter than the fixing nut.
View Details
100PC 3/8"USS FLT WASHER
Zinc steel flat washer with wide pattern is used to spread the load of a screwed fastening or when the hole is a larger diameter than the fixing nut.
View Details
$4.49
*SNAP FASTENER REFILL 1100A
Each refill kit contains 6 sets of fasteners without tools.
View Details
$7.49
*1110-SNAP FASTENER KIT
Replace broken or torn out snap fasteners. Each kit contains 6 sets of snap fasteners, the flaring tool and setting base. Snaps are nickel- plated. Studs are available for clamping onto canvas or a screw base for mounting on a hard surface.
View Details
$6.59
SNAP FASTENER KIT 1100
Replace broken or torn out snap fasteners. Each kit contains 6 sets of snap fasteners, the flaring tool and setting base. Snaps are nickel- plated. Studs are available for clamping onto canvas or a screw base for mounting on a hard surface.
View Details
$5.49
*SNAP FASTENER REFILL 1110A
Each refill kit contains 6 sets of fasteners without tools.
View Details
50PC 1/2" USS FLT WASHER
Zinc steel flat washer with wide pattern is used to spread the load of a screwed fastening or when the hole is a larger diameter than the fixing nut.
View Details
$8.99
KIT GROMMET 1/4"
Complete with tool and rustproof brass grommets for replacement or repairs in canvas or plastic. Instructions included. Tools with kit: Cutting block, hole cutter, inserting punch and die.
View Details
$11.99
KIT GROMMET 5/16"
Complete with tool and rustproof brass grommets for replacement or repairs in canvas or plastic. Instructions included. Tools with kit: Cutting block, hole cutter, inserting punch and die.
View Details
$11.99
3/8" HANDI GROMMET KIT
Complete with tool and rustproof brass grommets for replacement or repairs in canvas or plastic. Instructions included. Tools with kit: Cutting block, hole cutter, inserting punch and die.
View Details
$12.99
7/16" KIT GROMMET
Complete with tool and rustproof brass grommets for replacement or repairs in canvas or plastic. Instructions included. Tools with kit: Cutting block, hole cutter, inserting punch and die.
View Details
$12.99
KIT GROMMET 1/2"
Complete with tool and rustproof brass grommets for replacement or repairs in canvas or plastic. Instructions included. Tools with kit: Cutting block, hole cutter, inserting punch and die.
View Details
$4.99
GROMMET KIT REFILL 1/4"
Plain brass replacement grommets. Ideal for use with grommet kits.
View Details
$4.99
*GROMMET KIT REFILL 5/16"
Plain brass replacement grommets. Ideal for use with grommet kits.
View Details
$4.99
3/8" GROMMET KIT REFILL
Plain brass replacement grommets. Ideal for use with grommet kits.
View Details
$5.19
7/16" GROMMET KIT REFILL
Plain brass replacement grommets. Ideal for use with grommet kits.
View Details
$5.19
1/2" GROMMET KIT REFILL
Plain brass replacement grommets. Ideal for use with grommet kits.
View Details
$17.99
10-24X3 RND MACH SCREW
A machine screw is a fastening screw with a machine-cut thread throughout the length of its shank. Machine screws are used with nuts or screwed directly into a threaded receptacle to fasten various components together in machines, tools, etc. Fasten with a screwdriver to reduce risk of over-tightening and protect the screw and fastened material. If nuts are needed, use with nuts of the same finish and threading for proper fit. The length of a machine screw is measured from under the head to the point of the screw.
View Details
$8.19
3/16x6-/2" DR BIT,TAPCON
Carbide tipped tapcon. 135 deg (degree) tip angle. Shipped in quantities of 1.
View Details
$7.99
3/16x5-1/2 DR BIT,TAPCON
Carbide tipped tapcon. 135 deg (degree) tip angle. Shipped in quantities of 1.
View Details
3/16X1-1/4 FENDER WASHER
Zinc-plated. Packed 100 per box.Auxiliary retails reflect per each retail.
View Details
$57.99
*TAPPER 1000 INSTALL TOOL
Is a 2-step multipurpose tool designed to be used with all sizes and styles of Tapper fasteners. Can be used to both drill and drive the fastener. Fits the chuck of standard hammer drills.
View Details
$7.99
3/16x4-1/2 DR BIT,TAPCON
Carbide tipped tapcon. 135 deg (degree) tip angle. Shipped in quantities of 1.
View Details
$7.29
*3/16x3-1/2 DR BIT,TAPCON
Carbide tipped tapcon. 135 deg (degree) tip angle. Shipped in quantities of 1.
View Details
$8.99
8-10 PLASTC ANCHOR W/SCR
Recommended for light-duty static applications where holding power is not critical. For use in concrete, block, brick, and wallboard. Screws included.
View Details
10-24X2-1/2 MACH SCREW
A machine screw is a fastening screw with a machine-cut thread throughout the length of its shank. Machine screws are used with nuts or screwed directly into a threaded receptacle to fasten various components together in machines, tools, etc. Fasten with a screwdriver to reduce risk of over-tightening and protect the screw and fastened material. If nuts are needed, use with nuts of the same finish and threading for proper fit. The length of a machine screw is measured from under the head to the point of the screw.
View Details
$15.69
1/4-20X1-1/4 MACH SCREW
A machine screw is a fastening screw with a machine-cut thread throughout the length of its shank. Machine screws are used with nuts or screwed directly into a threaded receptacle to fasten various components together in machines, tools, etc. Fasten with a screwdriver to reduce risk of over-tightening and protect the screw and fastened material. If nuts are needed, use with nuts of the same finish and threading for proper fit. The length of a machine screw is measured from under the head to the point of the screw.
View Details
1/4-20X2-1/2 MACH SCREW
A machine screw is a fastening screw with a machine-cut thread throughout the length of its shank. Machine screws are used with nuts or screwed directly into a threaded receptacle to fasten various components together in machines, tools, etc. Fasten with a screwdriver to reduce risk of over-tightening and protect the screw and fastened material. If nuts are needed, use with nuts of the same finish and threading for proper fit. The length of a machine screw is measured from under the head to the point of the screw.
View Details
1/4-20X3 RND MACH SCREW
A machine screw is a fastening screw with a machine-cut thread throughout the length of its shank. Machine screws are used with nuts or screwed directly into a threaded receptacle to fasten various components together in machines, tools, etc. Fasten with a screwdriver to reduce risk of over-tightening and protect the screw and fastened material. If nuts are needed, use with nuts of the same finish and threading for proper fit. The length of a machine screw is measured from under the head to the point of the screw.
View Details
$15.79
*10-24x2 SCREW,MA FH
A machine screw is a fastening screw with a machine-cut thread throughout the length of its shank. Machine screws are used with nuts or screwed directly into a threaded receptacle to fasten various components together in machines, tools, etc. Fasten with a screwdriver to reduce risk of over-tightening and protect the screw and fastened material. If nuts are needed, use with nuts of the same finish and threading for proper fit. The length of a machine screw is measured from under the head to the point of the screw.
View Details
$62.99
1/2X6 BOLT ANCHOR
For attaching bottom plate or sill plate to newly poured concrete foundation. Meets ASTM A307 specifications. Washers and nuts included. 50-pieces per box. Available in 4 sizes.
View Details
$77.99
*1/2X8 BOLT ANCHOR
For attaching bottom plate or sill plate to newly poured concrete foundation. Meets ASTM A307 specifications. Washers and nuts included. 50-pieces per box. Available in 4 sizes.
View Details
*1/2X10 BOLT ANCHR
For attaching bottom plate or sill plate to newly poured concrete foundation. Meets ASTM A307 specifications. Washers and nuts included. 50-pieces per box. Available in 4 sizes.
View Details
$6.19
5/32X3-1/2 DR BIT.TAPCON
Carbide tipped tapcon. 135 deg (degree) tip angle. Shipped in quantities of 1.
View Details
